tools: cross point screwdriver, sharp vise, vise, allen wrench, Mobil EP0 grease, Mobil XHP 222 grease etc.
- sleeve coated with Mobil EP0 grease, that’s very important.
- install v-packing on airless sprayer piston rod
- install v-packing and sleeve in by using vise, and please make sure that the sleeve must be completely flat upon installed, otherwise the v-packing inside is not in correct position.
- install piston rod
- install motor / airless fluid pump / stand together
- tighten nuts
- check gear runs smooth or not.
- connect ground wire
- install gear box cover
- connnect motor line / power plug line / airless pressure regulator line etc.
- tighten all nuts for motor cover / front cover.
- Related products
- Related posts
- Video
- Comments
-
Tips for Operating X-3 and X-6(H) Airless Paint Sprayers
-
How do you know when to replace spray tip?
-
Airless Sprayers or HVLP Sprayers – What’s the Difference?
-
Comment peindre une chambre avec X25 Pulvérisateur Airless
-
How to adjust the electronic pressure if it is different with mechanical pressure?
-
Which airless sprayer can spray waterproofing polyurethane paint?
-
How to Select the Correct Airless Paint Sprayer
-
Airless sprayer to spray waterproofing acrylic coatings.
How to troubleshoot DP-X3 DP-X6 Airless Paint Sprayer
Pls follow below instructions to troubleshoot DP-X3 DP-X6 Airless Paint Sprayer.
Problem
Cause
Solution
Motor does not run:
(verify sprayer is plugged in, and ON/OFF switch is on)
Pressure control is set at zero pressure.
Turn pres...
Read more
DP-X3 X6 Airless sprayer won’t PRIME
There is nothing more frustrating than your airless paint sprayer not working. The paint pump is the thing that is supposed to make your job easier. However it has to draw paint and prime properly before it can work.
Inlet Valve Ball (pa...
Read more
spare parts for X3 X6 electric airless sprayer pump
Sparts Parts for X3/X6 Airless Paint Sprayer
Parts No.
Description
QTY
X5100a
Left cover
1
X5100b
Right cover
1
X5200
Front cover
1
X5300
Stand Assembly
1
X5301
Drip cup
1
...
Read more
X6 airless sprayer for PPG JONMAT Premium Contract Matt emulsion
[embed]https://www.youtube.com/watch?v=TKXa6nol570[/embed]
We tested our X6 airless paint sprayer with 519 tip size, for spraying the PPG JONMAT Premium Contract Matt Emulsion paint without water dilution, 32% volume solid.
The spraying pressur...
Read more
Tips for Operating X-3 and X-6(H) Airless Paint Sprayers
Tips/Guidance for Operating X-3 and X-6(H) Airless Paint Sprayers are as below for users' reference.
X-3 / X-6(H) airless paint sprayers are with OILESS DESIGN(PATENTED), no need to additionally add lubricating oil into the piston pump.
Pls c...
Read more
HOW TO ASSEMBLE MY X3 X6 DIY AIRLESS SPRAYER
tools: cross point screwdriver, sharp vise, vise, allen wrench, Mobil EP0 grease, Mobil XHP 222 grease etc.
sleeve coated with Mobil EP0 grease, that's very important.
install v-packing on airless sprayer piston rod
install v-packing and s...
Read more
HOW TO DISASSEMBLE MY X3 AIRLESS SPRAYER
tools: cross point screwdriver, sharp vise, allen wrench, alcohol, cotton swabs etc.
unscrew the nuts in front of cover by cross point screwdriver
unscrew the nuts of motor cover by cross point screwdriver
unplug airless puressure regulato...
Read more
