MENU
Rate this post

Airless Sprayer Safety

Airless Sprayer Safety

The most effective way to become familiar with operators safety and safety procedures is to read your owners manual THOROUGHLY. If you do not have the manual that came with the sprayer you are operating we encourage you to find a copy as airless sprayers are different from brand to brand and model to model, many can be downloaded.

Your safety is important! Careful use of airless spray equipment will prevent injuries!

Two major types of safety hazards exist with an airless paint sprayer:

Fire and Explosion

Fire and/or explosion can occur if the sprayer is spraying or flushing flammable fluid in an area where air circulation is poor and an open flame or sparks are present.

Many paints, solvents and their vapors will ignite, causing a fire or explosion which may burn you.The most common cause of a fire or explosion is the ignition of flammable vapors by an open flame or spark.

With an ungrounded spray system, the flow of fluid through the sprayer and hose may create enough static electricity to cause a spark from the gun. That spark can ignite flammable vapors.

Injection of spray material

Injection can be caused by high pressure fluid passing through a small opening, such as the spray tip or hose leak. This creates a high speed stream of atomized fluid which is powerful enough to pierce your skin and enter your body.

Injection occurs when the high pressure fluid pierces your skin.

The most common causes of injection are:

  • Placing your hand or body too close to the spray tip.
  • Grabbing a leaking hose or fitting, even if you are wearing gloves or using a rag.

The injury might look like “just a cut” but don’t be fooled! – It is a serious wound!

Get IMMEDIATE hospital treatment for any injection wound. Tell the doctor what fluid was injected.

 

“An ounce of prevention is worth a pound of cure”  Benjamin Franklin

 

Prevention

To help prevent a fire and/or explosion when spraying flammable or potentially flammable materials, always;

 

Spray in well-ventilated areas with good air movement. Use only non-sparking fans if one is needed.

Remove, extinguish or unplug all ignition sources such as…

cigarettes

pilot lights; stoves & ranges, water heaters, furnaces

all electric appliances

Put gas powered sprayers outside the building and run the hose into the room to be sprayed. Even though the sprayer is outside, always ground the sprayer to prevent static sparking.

Keep the work area free of debris that could contribute to a fire such as;

open or empty paint/material cans

open or empty solvent/thinner cans

rags, especially used ones

paper, masking

Prevent sparks and static sparking

Use only grounded hoses

Check hoses periodically for electrical continuity using and ohm meter.

Tape wall switches to help prevent them from being used

Use only grounded metal pails when spraying/painting, flushing or cleaning

Connect the pail to a true earth ground according to your local electric code.

Ground the sprayer regardless of the power source!

Electric Powered Sprayers

 

Plug into a properly grounded 3-wire outlet

You should check to make sure that the outlet is actually grounded. (see an easy and inexpensive way to)

Be sure the grounding prong is in place on the cord

If it is missing replace the plug

Use a grounded extension cord of at least 12 gauge wire and rated for 15 amps or more

(more you should know about extension cords)

Gas engine powered sprayers and air (pneumatic) powered sprayers

 

Connect the pail to a true earth ground according to your local electric code.

 

To help prevent injection injuries…

DP airless spray guns have a tip guard which helps prevent your hand or body coming too close tot he spray tip

Have the tip guard on the gun when spraying

Always use the spray gun trigger safety when not spraying

Relieve fluid pressure when cleaning or servicing any part of the equipment. To relieve pressure, shut off the sprayer, trigger the gun, and open the pressure drain valve.

Always point the gun away from yourself and others

Do not try and stop leaks with your hand or body

Follow the instructions manual when it comes to proper flushing methods, or visit our airless sprayer cleaning page

Remove the spray tip, reduce the material/fluid pressure and immerse the gun nozzle in the fluid when flushing

 

To help prevent accidentally triggering/ spraying the gun…

Put the trigger safety latch on when you are not spraying

This is a good habit to get into

Always keep the trigger guard on the gun! The guard helps prevent the trigger from being bumped or otherwise accidentally triggered

 

Other safety considerations

Wear safety glasses to protect your eyes from spray material / paint or solvent

Wear a respirator when using toxic or noxious paint or solvent.

Follow the material manufacturers guidelines to select the correct respirator and or cartridges

Read and save the instruction manuals supplied with the equipment. The manuals contain important information on airless spray safety

Every day thousands of painters safely use DP airless spray painting equipment by following these simple and effective precautions.

 

Please protect your safety by properly preparing the jobsite and carefully using the spray equipment. Play it safe for safety’s sake.


         
  • Related products
  • Related posts
  • Comments
  • FAQ

Leave your comments

Name *

Mail (will not be published) *

Country *

FAQ regarding our business

Q1: What's your MOQ minimum order quantity for formal order?

A: Our MOQ is 10-100 units depends on the model. For small pump or spray guns , the MOQ is 100. and for large capacity pump, the MOQ could be 10. We can accept 1 or 2 units for sample testing order.

Q2: What's your payment terms?

A: We could accept L/C, T/T and Paypal or Western Union, also accept the payment against B/L copy . We can offer credit payment term for our long year cooperated representatives.

Q3: What is the lead time?

A: Sample order: 3-5days, mass production 20-40 days for the formal order.

Q4: Can we put our logo on your products? Is there extra charge for it?

A: Yes, we accept the OEM order based on the order quantity. The color box package need extra cost for less container order.

Q5: What's your warranty?

A: our warranty is 12months limited warranty except the easily worn parts. and for the motor we offer 2 years warranty.

Q6. Which port do you ship your machines?

A: We ship from Ningbo port China. for the FOB price, we will bear the local freight charge and the forwarder fee / customs fee, and all the shipping cost / insurance cost / forwarder cost at destination port / import duty tax ... all will be beared by the buyer (or importer).

Q7. how can i buy your products?

A: if you're final user, please leave your mobile phone number to us, and we will ask our distributor / dealer to call you directly. if you want to be our distributor or representative, welcome to contact us by email or whatsapp. we can talk more details one by one, we're sure you would be satisfied with our quality / service and price.